interface ke všem moderním Yaesu transceiverům, umožňující digit8lní provoz.
Obsahuje USB zvukovou kartu a optopřevodníky
k oddělení signálů mezi TCVR a PC. K propojení s PC stačí pouze USB kabel.

obsah dodávky SCU-17

Yaesu SCU-17 interface
Anglický manual
USB A/B-kabel
audio kabel 2x 6pin Mini-DIN
Seriový kabel 2x 9pin SubD
2x 3.5mm stereo jack

Model Transceiveru Potřebné kabely
FT-450D stejné jako v balení SCU.17
FT-817ND Option CT-62
FT-857D Option CT-62
FT-897D Option CT-62
FT-950 stejné jako v balení SCU.17
FT-DX1200 stejné jako v balení SCU.17
FT-2000 (Variant 1) Option SCU-21
FT-2000 (Variant 2) vlastní výroba spolu s CT-39/A
FT-DX5000 (Variant 1) Option SCU-21
FT-DX5000 (Variant 2) vlastní výroba spolu s CT-39/A
FT-DX9000 (Variant 1) Option SCU-22
FT-DX9000 (Variant 2) vlastní výroba spolu s CT-39/A

Pomocí kabelů vlastní výroby lze SCU.17 využít prekticky se všemi ostatními transceivery jiných výrobců.
V uživatelském manuálu je specifikováno zapojení pinů SCU-17 interface

-----

The Yaesu SCU-17 is an interface to run with digital operating modes for almost all current Yaesu transceivers.
The SCU-17 works as a USB sound card, therefore only one USB cable is required between interface and
computer.
The interface isolates all signals galvanically to avoid potential ground loops.
In doing so the audio-in and audio-out, PTT, FSK and CAT signals are transmitted.
The key signals are seperated by Opto-isolators, the audio signals by coupling transformers.

The SCU-17 is protected by a metal box to avoid irradiation problems by HF.
There are two control knobs on the front panel for the NF-levels (Input, Output).
This way the modulation level is adjusted in seconds without having to bother with the sound card dialog of the
computer. Furthermore the front panel has three LEDs displaying the status of 'Power', 'PTT' and 'FSK'.
The SCU-17 uses the USB port as the power supply.

Shipment already includes several cables, which simplifies the use with current Yaesu transceivers.
Some models require an optional cable. The SCU-17 is designed in a way that even transceivers with a
classic RS-232 interface can be connected to modern computers via USB.

Installation requires to download and install the "Virtual COM Port Driver" from the website of Yaesu company.
Caution: Install prior to connecting the interface to your computer! Drivers can be found on www.yaesu.com
under 'Products', 'FT_DX1200', 'Files', 'SCU-17 USB Driver (Virtual COM Port Driver)'.

Shipment SCU-17

Yaesu SCU-17 interface
Printed user manual (english)
USB A/B-cable
NF-cable 2x 6pin Mini-DIN
Serial cable 2x 9pin SubD
2x 3.5mm stereo jack
Transceiver Required cables
FT-450D same as shipment
FT-817ND Option CT-62 needed
FT-857D Option CT-62 needed
FT-897D Option CT-62 needed
FT-950 same as shipment
FT-DX1200 same as shipment
FT-2000 (Variant 1) Option SCU-21 needed
FT-2000 (Variant 2) self-made with CT-39/A needed
FT-DX5000 (Variant 1) Option SCU-21 needed
FT-DX5000 (Variant 2) self-made with CT-39/A needed
FT-DX9000 (Variant 1) Option SCU-22 needed
FT-DX9000 (Variant 2) self-made with CT-39/A needed

Of course, with self-made cables you can connect virtually all other transceivers, of other manufacturers as well.
The pin configuration of the SCU-17 interface is specified properly in the user manual.