Můžete se přihlásit anebo si založit konto
CZK Košík

LDG Z-100A autom. ant. tuner

LDG  Z-100A autom. ant. tuner
auto tuner 1,8-54 MHz, 125W

Cena s DPH 6 290,00 CZK

Cena bez DPH5 198,35 CZK

ks
Odkazy
auto tuner 1,8-54 MHz, 125W PEP CW/SSB, 30W PSK/FT8/RTTY
2000 pamětí, rozsah přizpůsobení 4 až 800 ohmů, v pásmu 6m 15-150 ohmů

koaxiální výstup, možnost připojení drátových nebo symetrických antén přes externí balun. (např. BL1/4 od Elecraft, Eco aj.)
doba ladění 1 až 6 sec, průměr. 3 sec, (v paměťovém režimu min. 0,1 sec)
Rozměry: 12,7 x 12,7 x 3,8 cm
napájení 7 až 18V/200mA během ladění

Pro použití s většinou transceiverů Icom.
Součástí dodávky je propojovací kabel k Icom transceiverům.


-----

Technical Description Z-100A
The LDG Z-100A is an automatic antenna tuner for shortwave up to 6m. The tuner tunes all coax fed antennas like dipoles, verticals etc.
For certain wire antennas a LDG 1:4 or 1:1 balun can be used.

Tuning is done automatically and when using the supplied cable with an Icom radio, by pressing the "Tune" button on the radio.
This cable also supplies power to the tuner. When tuning for the first time, the values found are stored in one of 2000 memories; if the
same frequency is used again later, the values are read from the memory. Tuning thus takes less than a second.

The maximum permissible transmit power is 125 W PEP (SSB, AM, CW) or 30 W for digimodes (FT-8, RTTY etc.) The tuning range is 4 to 800 ohms.

Application Description Z-100A
The Z-100A makes life easier on shortwave. You don't always have optimally tuned antennas at your disposal, so a tuner has to take care of the
necessary adjustment.

The Z-100A works with coaxial fed antennas like windom, dipole or zepp antennas, but also with verticals or loops. The tuning range of 4 to 800 ohms
can compensate for a mismatch of 10:1, which is far more than most built-in tuners can do.

Operation is automatic with most Icom transceivers, either by pressing the "Tune" button, or when pressing the PTT button. The supplied cable
with the 4-pin Icom tuner connector can be used with most Icom transceivers made in the last 30 years. Check the manual for details: If your radio
supports the Icom AH-4 tuner you can use the LDG Z-100A without any problems.

Connection cable for Icom IC-706, 703, 718, 7000, 7100, 7200, 7300, 7410, 746, 756, 7600, 7610 (and all variants), 35 cm


Product Name Z-100A
Impedance Range (?) 4 - 800 Ohm
Min. Tune Power (W) 0.1 W
Current Intake (A) 500 mA
Supply Voltage 13.8V +-15%
Display LED
Remote Control capabilities yes
Number of Memories 2000
Tuner type Automatic Tuning
Suitable for All Icom with 4 pin tuner socket
Max. Power [W] 125 W
Frequency Range 1.8 - 54 MHz
Documentation Languages EN
Size W x H x D 165 x 32 x 165 mm
Weight [kg] 0.68 kg


0.1 to 125 Watt SSB/CW, 30W Digital.
2000 memories for instantaneous band changing.
Controlled from Icom Tuner button on radio or Push button on Tuner.
Compatible with any Icom radio that is AH-4 or AH-3 compatible. (6M tuning from Tuner button for radios that are only AH-3 compatible)
Partial radio list: IC-706, 703, 718, 7000, 7100, 7200, 7300, 7410, 746, 756, 7600, 7610 (and all variants).
Tuning time: 0.1 to 6 seconds full tune, 0.1 seconds memory tune.
1.8 to 54.0 MHz coverage. Built-in frequency sensor.
Tunes 4 to 800 ohm loads (16 to 150 on 6M)
For Dipoles, Verticals, Vs, Beams or any Coax Fed Antenna.
Includes Icom interface cable. Ready to use out of the box.
Small Size Enclosure: 6.5” L x 6.5” W x 1.25” H.
Weight: 1.5 pounds.