Můžete se přihlásit anebo si založit konto
CZK Košík

Expert Electronics SunSDR2 DX

Expert Electronics SunSDR2 DX
DUC/DDC HF/6m/VHF SDR TCVR with Ethernet interface

Cena s DPH 53 980,00 CZK

Cena bez DPH44 611,57 CZK

ks
Odkazy
špičkový DUC/DDC HF/6m/VHF SDR TCVR

DDC SDR TCVR s Ethernet interface

verze r. 2021

rozdíly proti SunSDR PRO2:

výkon 100W na KV a 50 W na 50 MHz
konektor ATU pro ovládání ant. tuneru
přidaný HP filtr pro vylepšení vlastností na 2m
přidaný filtr pro KV
vylepšený předzesilovač LNA na 2m
nový 24 bit stereo audio codec
nový napájecí konektor typu Anderson
přidaný konektor uzemnění
vylepšená deska plošného spoje
nižší spotřeba
dokonalejší distribuce energie

softwarově definovaný transceiver s rozsahem 9 kHz - 65 MHz a 95-148 MHz
Na rozdíl od jiných SDR, které se standardně připojují k PC pomocí USB kabelu, zde komunikaci zajišťuje síťový
ethernet kabel.

To má výhodu v mnohem větší rychlosti přenosu mezi přijímačem a PC, umožňuje použití delších kabelů a
integraci SDR do místní sítě a remote provoz.



SDR se dodávaným kabelem připojí buď přímo k PC nebo do routeru.

Specifikace:

Frekvenční rozsah 9 kHz – 65MHz (RX), všechna am. pásma KV/6m (TX)
Frekvenční rozsah VHF 95-148 MHz (RX), 144-146 MHz (TX)
citlivost 0,07 uV
Výkon TX 100 W (HF), 50W (50 MHz), 8 W (VHF)
Blocking Dynamic Range 129 dB (HF), >114 dB (VHF)
RF ADC clock freq. 160 MHz
RF DAC clock freq. 640 MHz
RF DAC resolution 14 bit
napájecí napětí 15V (12 až 16 V)

stabilita místního oscilátoru +/-0,5ppm
built-in audio codec resolution 24 bit


-----

The SunSDR2 DX transceiver based on the well-known SunSDR2 PRO transceiver with several hardware
improvements.
It is a 100W-HF; 50W-6M; 8W-2M transceiver, very compact, has active cooling and
improved supply system, meaning it’s perfectly suited for DXpeditions. Also, we've added a separate connector for an
external ATU, thus SunSDR2 DX has all the functionality you got used to in our radios and even more.
Improved hardware along with the ExpertSDR2 software makes this high-performance SDR transceiver the perfect
base station. The evident choice for a true contester!

Hardware improvements in comparison to SunSDR2 PRO:

HPF for VHF (100 MHz) to eliminate strong out-of-band stations coming from HF
LPF for HF (70 MHz) to eliminate strong out-of-band stations coming from VHF
New VHF LNA chip - PGA103+
New high-performance built-in stereo audio codec 24-bit with 114 dB dynamic range (CS4272)
Improved supply system, which leads to less heating and less power consumption
Active cooling
Antenna switch supports Predistortion without external devices
Improved topology of SDR PCB


Main capabilities

Independent RX path based on DDC (Direct Down-Conversion) architecture
Independent TX path based on DUC (Direct Up-Conversion) architecture
Output power: 100W on HF, 50W on 6M and 8W on 2M
2 software RXs + SubRX for each of them (4 slices total) + independent wideband Bandscope up to 80 MHz
Remote control operation, using it, you connect PTT and CW-key to the E-Coder panel. Microphone and E-Coder are connected to the remotely set up PC
TCI interface for seamless connection with third-party software, the list of software with TCI support
Professional TX processing module provides the most advanced tuning capability for voice operation
ExtCTRL connector to control external devices with 8 powerful keys with open collector
ALC connector for external power amplifiers*
Supports use of VHF transverters
An opportunity to use the transceiver as a signal generator via DAC OUT connector (SMA connector)
An opportunity to use external filters in the middle of the RF path, using ADC IN and RX OUT (SMA connector)
Monitoring delay in CW mode is about 2-3 ms
Input for external 10 MHz reference oscillator
An opportunity to use the transceiver in SO2V mode
Antenna switch with 2 HF antenna connectors and separate VHF antenna connector (Mini UHF connectors)
Internal power-meter for HF and VHF bands and SWR-meter for HF band
Ethernet LAN interface provides a fast and reliable connection to PC

The ExpertSDR2 minimal system requirements:

2 or 4 core CPU Intel Core i3 or Core i5;
8 GB RAM;
40 GB free space on the HDD/SSD for the ExpertSDR2 and accompanied programs;
17' or bigger monitor;
video card with OpenGL 1.5 or higher;
The ExpertSDR2 software supports Windows 7-10 32/64 bit, Linux (Ubuntu/Kubuntu 18.04 x64), and macOS
10.14 Mojave and higher.

SunSDR2 DX complete set

Transceiver SunSDR2 DX
External fan, size 140 x 140 mm
LAN-cable for connection to a local network (1.8m)
Power cable for connection to a power supply (2m)
Audio-adapters JACK 6.3mm to JACK 3.5mm (2 pcs.)
RF Cable Mini UHF — HF PL259 1Ft (0.3m 1 pc.)

Additional accessories:

E-Coder Plus or E-Coder control panel for comfortable tuning